- Get Free Suzuki Df6 Outboard Service Manual Suzuki Df6 Outboard Service Manual Getting the books suzuki df6 outboard service manual now is not type of challenging means. You could not unaided going taking into consideration book heap or library or borrowing from your associates to admission them. This is an certainly easy means to specifically get.
- Suzuki Outboard Service Repair Manual PDF Free 4-Stroke 2-Stroke, DF4 DF5 DF9.9 DF15 DT225 DT150 DT175 DT200 DT115 DT140 DF DT DF200 DF225 DF250 ≡ Menu Suzuki Service Manuals.
Suzuki Factory Service Repair Manuals in pdf format download free. Suzuki workshop manuals. 2010 suzuki 9.9 hp outboard owners manual; 2010 suzuki df6 service manual; 2010 suzuki four stroke 200 hp shop manuel; 2008 suzuki 140 hp 4 stroke outboard exploded view; 2008 suzuki 175 4 stroke outboard manual; 2008 suzuki 9.9 outboard lower gear oil screws; 2003 suzuki.
RELATED SUZUKI OUTBOARD SEARCHES:
PROPELLERS
An outboard motor is designed to develop its rated power within a specified engine speed range. The maximum rated power delivered by the Suzuki models are shown in your service manual. If the standard propeller fails to meet the above requirement, use another pitch propeller to hold the engine speed within the range specified in your manual propeller selection chart.
Installing a propeller with pitch either too high or too low will cause incorrect maximum engine speed, which may result in severe damage to the motor.
Disassembly of propeller shaft components
1. Slide propeller shaft away from reverse gear housing assembly
Account for reverse gear back-up shim thrust washer
2. Remove horizontal slider and forward gear thrust washer
3. Remove spring
4. Using special tool, push dog pin shifter.
5. Remove clutch dog shifter propeller shaft.
PROPELLER
• Inspect propeller for bent, chipped or broken blades and replace or repair if necessary.
• Inspect propeller bushing splines for wear or other damage and replace if necessary.
• Inspect propeller bushing for deterioration or slipping and replace if necessary.
PROPELLER SHAFT COMPONENTS
• Inspect horizontal slider and connector pin for excessive wear or other damage. Replace if necessary.
• Inspect clutch dog shifter for excessive wear, chip or other damage. Replace if necessary.
• Inspect dog pin for bent or other damage. Replace if necessary.
• Inspect propeller shaft / splines for wear, twist or other damage. Replace if necessary.
PROPELLER SHAFT BEARING HOUSING
• Inspect housing for cracks or other damage. Replace if necessary.
• Inspect propeller shaft bearings and reverse gear bearing for pitting, rough or other damage. Replace if necessary.
• Inspect oil seals and O-ring for cuts, nicks or tears.
Replacing propeller shaft oil seal
1. Remove retaining ring
2. Extract oil seals
1 and washer 2.3 using oil seal remover.
Do not re-use oil seal once removed.
Always use a new oil seal.
3. Apply Water Resistant Grease to inner circumference of housing.
4. Using an oil seal installer, drive two oil seals (one at a time) into housing.
The lipped portion of seal should face towards propeller.
Apply Water Resistant Grease to seal lips.
5. Install washer and retaining ring.
PROPELLER INSTALLATION
1. Install spacer shaft, then slide on propeller
2. Fit spacer specified torque.
1 and propeller stopper 2 onto propeller3.4, washer 5 and nut 6, then tighten nut to
Propeller nut : 55 N.m (5.5 kg-m, 40.0 lb.-ft.)
3. Push cotter pin secure.
Suzuki Df6 Owners Manual Free
PROPELLER SELECTION FOR COUNTER
ROTATION
Suzuki Df6 Service Manual
For counter-rotation model, newly designed stainless steel propellers are available as follows.
Suzuki Df6 Service Manual Pdf
Suzuki highly recommend to use the genuine Suzuki counterrotation propeller for the counter rotation model. In case of twin installation, always use on both engines, the same size normal rotation and counter-rotation propellers.
Suzuki Df6 Owners Manual Online
ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)
UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)
Suzuki Df6 Outboard Owners Manual
• Incorrect by-pass air screw adjustment [NOTE3]
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)